Airport Service Truck Black Smoke Purifier (DPF)

Purification rate 90%+
Gas processing volume Per vehicle model
Element life Washable metal elements
Regeneration 1-min water rinse
Customisation Service trucks

Product Introduction

Fuel, catering, water, waste — service trucks creep and stop all day and never build exhaust temperature. The A3 replaces heat regeneration with depth filtration in a metal element, so cold short runs do not coke it up, and its mounting clears both the PTO and the body doors.

Specifications

Product characteristicsMetal, washed
Processing and customizationYes
BrandAIFILTECH
Gas processing volumePer vehicle model
Purification rate90%

Detailed Overview

01 Product Introduction

The AIFILTECH Airfield Service Truck Exhaust Purifier A3 (for service trucks) is installed after the exhaust line of airfield service trucks. Its core is a AIFILTECH water-washable regenerative metal filter element (metal DPF, patent No. ZL 2018 1 0598975.7), delivering over 90% particulate filtration efficiency with one-minute water-wash regeneration. Nearly 5,000 units are in service nationwide.

Gas processing volume is customised to the engine displacement. Stainless steel or powder-coated carbon steel housing; mounting and connections arranged to the chassis space.

AIFILTECH airport service truck exhaust purifier (front)

02 Working Principle

Exhaust gas emitted by the diesel engine enters the AIFILTECH purifier at the inlet. The gas, laden with carbon particles, passes from the outside to the inside through the wall of each AIFILTECH water-washable metal filter element (metal DPF, patent No. ZL 2018 1 0598975.7), where the particles are captured; the clean gas leaves through the outlet.

The purifier is connected in-line after the vehicle's original exhaust pipe. Hot exhaust is filtered by the AIFILTECH metal elements; black smoke and carbon particles are held on the element surfaces while the cleaned gas discharges through the outlet. The compact element layout keeps back pressure low and barely affects vehicle performance.

Exhaust purifier structure diagram (air inlet, AIFILTECH filter element, supporting plate, mounting bracket, exhaust outlet, back pressure gauge)

As the vehicle runs, carbon particles accumulate on the element surfaces and back pressure gradually rises. Once it reaches the set value (typically 25 kPa), shut down the engine, release the clamps, pull out the elements and rinse them under a tap; refit and re-tighten the clamps and the unit is ready again. Regeneration takes about one minute — no replacement elements or consumables are needed.

backpressure curve

03 Product Advantages

  • Particulate filtration efficiency over 90% ; measured light absorption coefficient below 0.5 m⁻¹ and Ringelmann smoke density below 1;
  • Easy maintenance: 1-minute water-washing regeneration, reusable without damage;
  • Easy installation: clamp-on design, 30-second quick disassembly, no modification to the original exhaust routing;
  • No secondary pollutants; no fuel additives, urea or other consumables required;
  • All-metal housing and elements with heat, thermal-shock and vibration resistance, suited to high-frequency airport operations;
  • Compact and lightweight: underbody-mounted, side-mounted or tail-mounted, leaving cargo and operation space untouched;
  • Customised to engine displacement and chassis space, covering towing tractors, shuttle buses, pickups, tractors, rescue trucks and other airport vehicles.

04 Certifications & Application Cases

The unit was tested by an independent laboratory holding CMA and CNAS accreditation; the measured light absorption coefficient was below 0.5 m⁻¹.

Since the AIFILTECH water-washable regenerative metal purifier was successfully developed, this core product line has accumulated nearly 5,000 installed cases in the after-treatment industry. We joined the non-road retrofit programmes in Nanjing as early as 2018 and have completed nearly 1,000 installations in that market alone, with users across the country. The products have been applied in demanding non-road sites such as Beijing Capital International Airport, Guangzhou Baiyun International Airport, Xiamen Airport, Nanchang Airport and Nanning Airport. Airport ground support equipment is one of the key application fields of AIFILTECH exhaust purifiers.

Applicable: diesel airport ground support vehicles and non-road machinery of all makes. Selection calculation, installation guidance and commissioning support are available.

Sizing & selection Q&A

Which rating fits my machine?

Same displacement usually shares one unit across engine brands, so the plate photo is enough to match it.

What smoke opacity can it hold?

The test conditions sit in the datasheet. What counts after installation is the re-test reading, not the catalogue number.

Do I ship the core back for regeneration?

No return shipment. Pull the unit, rinse the core, clamp it back — the substrate is reused, not consumed.

Can it be fitted before an inspection date?

Direct fit, no pipe cutting, and a single unit goes on inside an inspection window. The clamp design also comes off fast.

How do I match a foreign test method?

Send the local test method and limit value; the model and the acceptance evidence are matched to that method rather than to a generic claim.

Applications

Airport ground support vehicles Baggage towing tractors Aircraft towing tractors Shuttle buses Airport pickups and patrol vehicles Field rescue trucks Airport tractors Forklifts Construction machinery Port terminals Non-road machinery

All data above are obtained under specific test conditions; the actual solution must be engineered to site conditions. AIFILTECH provides custom design and sizing based on actual gas volume, temperature, dust characteristics and emission limits.

WhatsApp