Airport Terminal Tractor Black Smoke Purifier (DPF)

Purification rate 90%+
Gas processing volume Per vehicle model
Element life Washable metal elements
Regeneration 1-min water rinse
Customisation Tractors

Product Introduction

A ramp tractor is not a baggage tractor: it pulls more, starts more often, and sits lower. The A4 is sized to towing capacity and ground clearance, with the shell flattened so its lowest point stays above the frame rail.

Specifications

Product characteristicsMetal, washed
Processing and customizationYes
BrandAIFILTECH
Gas processing volumePer vehicle model
Purification rate90%

Detailed Overview

01 Product Introduction

The AIFILTECH Airfield Tractor Exhaust Purifier A4 (for tractors) is installed after the exhaust line of airfield tractors. Its core is a AIFILTECH water-washable regenerative metal filter element (metal DPF, patent No. ZL 2018 1 0598975.7), delivering over 90% particulate filtration efficiency with one-minute water-wash regeneration. Nearly 5,000 units are in service nationwide.

Gas processing volume is customised to the engine displacement. The open engine bay and heavy vibration of tractors are addressed with customised mounting and damping.

AIFILTECH airport tractor exhaust purifier (front view)

02 Working Principle

Exhaust gas emitted by the diesel engine enters the AIFILTECH purifier at the inlet. The gas, laden with carbon particles, passes from the outside to the inside through the wall of each AIFILTECH water-washable metal filter element (metal DPF, patent No. ZL 2018 1 0598975.7), where the particles are captured; the clean gas leaves through the outlet.

The purifier is connected in-line after the vehicle's original exhaust pipe. Hot exhaust is filtered by the AIFILTECH metal elements; black smoke and carbon particles are held on the element surfaces while the cleaned gas discharges through the outlet. The compact element layout keeps back pressure low and barely affects vehicle performance.

Exhaust purifier structure diagram (air inlet, AIFILTECH filter element, supporting plate, mounting bracket, exhaust outlet, back pressure gauge)

As the vehicle runs, carbon particles accumulate on the element surfaces and back pressure gradually rises. Once it reaches the set value (typically 25 kPa), shut down the engine, release the clamps, pull out the elements and rinse them under a tap; refit and re-tighten the clamps and the unit is ready again. Regeneration takes about one minute — no replacement elements or consumables are needed.

backpressure curve

03 Product Advantages

  • Particulate filtration efficiency over 90% ; measured light absorption coefficient below 0.5 m⁻¹ and Ringelmann smoke density below 1;
  • Easy maintenance: 1-minute water-washing regeneration, reusable without damage;
  • Easy installation: clamp-on design, 30-second quick disassembly, no modification to the original exhaust routing;
  • No secondary pollutants; no fuel additives, urea or other consumables required;
  • All-metal housing and elements with heat, thermal-shock and vibration resistance, suited to high-frequency airport operations;
  • Compact and lightweight: underbody-mounted, side-mounted or tail-mounted, leaving cargo and operation space untouched;
  • Customised to engine displacement and chassis space, covering towing tractors, shuttle buses, pickups, tractors, rescue trucks and other airport vehicles.

04 Certifications & Application Cases

The unit was tested by an independent laboratory holding CMA and CNAS accreditation; the measured light absorption coefficient was below 0.5 m⁻¹.

Since the AIFILTECH water-washable regenerative metal purifier was successfully developed, this core product line has accumulated nearly 5,000 installed cases in the after-treatment industry. We joined the non-road retrofit programmes in Nanjing as early as 2018 and have completed nearly 1,000 installations in that market alone, with users across the country. The products have been applied in demanding non-road sites such as Beijing Capital International Airport, Guangzhou Baiyun International Airport, Xiamen Airport, Nanchang Airport and Nanning Airport. Airport ground support equipment is one of the key application fields of AIFILTECH exhaust purifiers.

Applicable: diesel airport ground support vehicles and non-road machinery of all makes. Selection calculation, installation guidance and commissioning support are available.

Sizing & selection Q&A

How is the unit sized to my engine?

Three inputs settle it: rated power or displacement, exhaust pipe diameter, and duty cycle (continuous or intermittent). No guesswork on the model number.

Is the efficiency figure measured or nominal?

The figure comes from a standard-condition test, not from any duty cycle. Load factor, fuel sulfur and backpressure all move the measured number.

How often does it need servicing?

There is no fixed interval; watch backpressure and smoke colour. Idle-heavy duty and poor fuel bring it on sooner. A wash takes a minute.

Any chassis modification needed?

No cutting and no chassis work. It clamps at the original silencer location and releases in about 30 seconds for transfer or inspection.

Which limit does it target?

It is built to the in-use limit of the target market, not to another country’s standard. A common path: fit one unit, re-test, then scale.

Applications

Airport ground support vehicles Baggage towing tractors Aircraft towing tractors Shuttle buses Airport pickups and patrol vehicles Field rescue trucks Airport tractors Forklifts Construction machinery Port terminals Non-road machinery

All data above are obtained under specific test conditions; the actual solution must be engineered to site conditions. AIFILTECH provides custom design and sizing based on actual gas volume, temperature, dust characteristics and emission limits.

WhatsApp