AIFILTECH 316L Sintered Stainless Steel Fiber Felt

Filtration Rating 3~100μm
Porosity 68%~85%
Models BZ3D~BZ100D

Product Introduction

316L stainless steel fiber felt is sintered from multi-layer laid fiber - high porosity, high dirt capacity, repeatable back-flush and water-wash regeneration, 2-100 um rating - for polyester and chemical fiber polymer filtration, hot gas dedusting and catalyst recovery.

Specifications

型号系列BZ3D / BZ5D / BZ10D / BZ15D / BZ20D / BZ25D / BZ30D / BZ40D / BZ60D / BZ100D
平均Filtration rating3-100 μm
孔隙度68%-85% (±5%)
气泡点压力630-12300 Pa (±8%)
透气度≥10-1220 L/(min·dm²) (随型号)
Temperature480 ℃ (氧化气氛)/ 550 ℃ (还原气氛)

Detailed Overview

01 Product Overview

Stainless fibers of 2-40 um are laid into multi-layer felts with graded pore structure, then vacuum-sintered to bond fiber crossings. The media combines high porosity (70-90%) with high strength and far higher dirt capacity than woven mesh or sintered powder. It can be pleated into large-area cartridges or made into discs and plates.

02 Performance & Mechanism

316L stainless steel sintered fiber felt is made of micron-grade steel fiber (1.5-30 μm diameter), non-woven into webs, layered in pore-size gradient and sintered into a 3D porous structure. Porosity 68-85% gives high dirt-holding capacity and slow pressure rise; filtration rating 3-100 μm across ten models (BZ3D-BZ100D), bubble point 630-12300 Pa, permeability up to 1220 L/(min·dm2). More clogging-resistant than woven mesh and stronger with higher flow than powder sintered parts, it serves chemical fiber, hot-gas filtration, petrochemical and hydrogen applications.

03 Advantages

  • 70-90% porosity, low pressure drop, high dirt capacity; 2. 2-100 um rating with controllable gradient; 3. Repeatable back-flush, water-wash and chemical regeneration; 4. About 600 °C in oxidizing atmosphere, weldable; 5. Pleatable, rolled and framed into cartridges.

04 Applications

For polyester and chemical fiber polymer filtration, steam and heat-transfer fluid filtration, catalyst recovery, fluidized bed distribution and coalescing separation. Cartridges, discs and custom assemblies available.

05 Filtration Data (Stainless Steel Fiber Felt)

Stainless steel fiber felt comes in ten grades from 3 to 80μm. Bubble point, permeability, porosity, weight, thickness and dirt capacity are listed below; grade selection follows medium viscosity and the target rating, with custom specs available.

GradeBubble point (Pa)Permeability (L/min·dm²)Porosity (%)Weight (g/m²)Thickness (mm)Dirt capacity (mg/cm²)
3μm12000106010500.301
5μm7000307010000.402
10μm35001007510500.504
15μm23001808010500.6810
20μm17003008010500.6815
25μm14003508010500.6815
30μm11006008010500.6818
40μm9006508010500.6825
60μm8001000858500.6830
80μm7001300858500.6840
AIFILTECH 316L stainless steel fiber sintered feltAIFILTECH fiber felt microstructureAIFILTECH felt backlit porosity view

Sizing & selection Q&A

How do rating and flux trade off?

Adjustable within 3-100 μm. Finer rating costs flux, so the practical route is to work back from the allowed pressure drop.

Do you take customer drawings?

We do — a drawing or a sample is enough to start, with tolerances agreed before quoting.

What is the delivery time?

stock items go out same day, non-standard follows the production schedule.

How is a sample charged?

Samples are quoted as a small batch and credited against the volume order, per the quotation.

Applications

Polymer filtration Hot gas dedusting Catalyst recovery Custom

All data above are obtained under specific test conditions; the actual solution must be engineered to site conditions. AIFILTECH provides custom design and sizing based on actual gas volume, temperature, dust characteristics and emission limits.

WhatsApp