AIFILTECH Cylindrical Insulated Genset Exhaust Purification System

Purification rate 90%+
Gas processing volume Per genset rating
Element life Washable metal elements
Regeneration 1-min water rinse
Customisation Ceiling/floor/roof

Product Introduction

In cold-climate plant rooms and outdoor container sets, skin temperature is a safety-inspection item. This engineered package wraps the cylinder in insulation under a stainless jacket, bringing surface temperature down while cutting heat loss along the run.

Specifications

Product characteristicsMetal, washed, insulated
Processing and customizationYes
BrandAIFILTECH
Gas processing volumePer genset rating
Purification rate90%

Detailed Overview

01 Product Introduction

The AIFILTECH Cylindrical Insulated Genset Exhaust Purification System is a complete exhaust treatment package for high-power generator sets and stationary power plants, consisting of cylindrical (tank-type) purification units, insulation cladding, bellows piping, fan/stack interfaces and an electrical control system. Its core is the AIFILTECH water-washable regenerative metal filter element (metal DPF, patent No. ZL 2018 1 0598975.7), delivering over 90% particulate filtration efficiency with one-minute water-wash regeneration.

Gas processing volume is engineered to the genset rating; units can be ceiling-hung, floor-mounted or roof-installed. Insulation cladding keeps surface temperature and engine-room heat load low, with stainless or aluminised-zinc outer sheet.

Site profile: high-power gensets and power plants run large, continuous exhaust flows and need a purification system that is engineered, delivered and commissioned as a complete package.

AIFILTECH genset exhaust purification system installed in generator room

02 Working Principle

Genset exhaust enters the cylindrical purifier through the bellows piping and passes from outside to inside through the wall of each AIFILTECH element; carbon particles are held on the element surfaces and the cleaned gas leaves through the outlet manifold into the stack. Where tanks are installed in parallel, groups can be brought online or offline according to load.

Once the elements are loaded, the back-pressure signal prompts regeneration: shut down, open the quick-release clamps, rinse the elements and refit — the unit returns to service. Insulation keeps the tank surface within a safe temperature range and reduces heat radiation into the engine room. The control system monitors back pressure, valve position and fan status in one place, with automatic alarms.

Exhaust purifier structure diagram (air inlet, AIFILTECH filter element, supporting plate, mounting bracket, exhaust outlet, back pressure gauge)

03 Product Advantages

  • Particulate filtration efficiency over 90% with consistent compliance; measured light absorption coefficient below 0.5 m⁻¹;
  • Complete delivery: purification units, insulation, piping and controls engineered and commissioned as one package;
  • One-minute water-wash regeneration, low maintenance, elements reused without damage;
  • Cylindrical tank offers good pressure and load behaviour — ceiling, floor or roof installation;
  • Insulation cladding lowers surface temperature and engine-room heat load;
  • Centralised monitoring of back pressure, valve position and fan status with remote access;
  • All-metal housing and elements: heat, thermal-shock and damage resistant.

04 Certifications & Application Cases

The purification units in this system were tested by a laboratory holding CMA and CNAS accreditation; the measured light absorption coefficient was below 0.5 m⁻¹.

AIFILTECH water-washable regenerative metal purifiers have accumulated nearly 5,000 installed cases. Products have been applied in demanding non-road sites such as Beijing Capital International Airport, Guangzhou Baiyun International Airport, Xiamen Airport, Nanchang Airport and Nanning Airport, and are widely used in genset rooms, ports and industrial power plants. Selection calculation, system design, installation guidance and commissioning support are available.

AIFILTECH multiple black smoke purifier units on rooftop

Sizing & selection Q&A

Which rating fits my machine?

Same displacement usually shares one unit across engine brands, so the plate photo is enough to match it.

What smoke opacity can it hold?

The test conditions sit in the datasheet. What counts after installation is the re-test reading, not the catalogue number.

Do I ship the core back for regeneration?

No return shipment. Pull the unit, rinse the core, clamp it back — the substrate is reused, not consumed.

Can it be fitted before an inspection date?

Direct fit, no pipe cutting, and a single unit goes on inside an inspection window. The clamp design also comes off fast.

How do I match a foreign test method?

Send the local test method and limit value; the model and the acceptance evidence are matched to that method rather than to a generic claim.

Applications

Diesel generator sets Construction machinery Forklifts Marine auxiliary engines Mining equipment Engine test benches Emergency power trucks Tunnel construction Airports Port terminals Construction sites Municipal roads

All data above are obtained under specific test conditions; the actual solution must be engineered to site conditions. AIFILTECH provides custom design and sizing based on actual gas volume, temperature, dust characteristics and emission limits.

WhatsApp